How to install and programming an LED sign board

Each LED board contain 3 basic parts: LED module, controller, power supply
LED module
LED modules can connect together to make a big display. there are single color LED modules, 2colors and full colors(RGB) LED modules.
since traditionally LEDs when leaves in sunlight for long time loss its first brightness, so
that modules make by special LEDs that have higher resistance to sun ray.
 
How to make a programmable LED board

Controller
controller (some time call mother board) contain LED display driver, memory and back up battery.

How to make a programmable LED board

Power supply
power supply is a 5v regulated adapter and its current is between 1A to 50A or more (according to number of modules that make bigness of display)
Note: connecting + and - in reverse causes damage for both controller and LED modules.

How to make a programmable LED board
Programing process
For programming the LED board first must install "HD2013" program on your computer.
You can download it from following link(password=168):
https://drive.google.com/open?id=0B4jg9KxpTKGTeWZzbU11Yl82cG8 when installing completed select your controller board model (i used HD-A40)
Follow this steps:

How to make a programmable LED board

How to make a programmable LED board

then insert number of LEDs in width and in height of your LED display and then select the type of your module (mine is P10 >> 10 in fact is the distance between centers of two near LEDs in millimeter . that make resolution of LED display >>> lower number=better resolution )

How to make a programmable LED board

 "default setting" must be turn off

How to make a programmable LED board

 then select the luminance and select frequency of refresh then click finish.

How to make a programmable LED board

now connect the controller to your computer and click on program then text 

How to make a programmable LED board 

in black area type the text that want to show in your LED display then click send to save it on your controller even after disconnecting the USB cable.
You can add many beautiful effect to your text and can change its color if your module is RGB.

How to make a programmable LED board

How to make a programmable LED board
Review >> use for test how text will displayed
U disk >> use for save the program on USB flash
Time >> use for show the calender on your display
Clock >>use for show the time on your display
Temp >>use for show the temperature on your display
Count >> use for counting days of week or month or year reversely on your display
send >> use for save the program in controller
hypertext >> use for convert some picture to displayable picture on LED module

Please subscribe to my YouTube channel here: 
https://www.youtube.com/c/EngMousaalkaabi?sub_confirmation=1


Lokasi: United States

Komentar

Posting Komentar

Postingan populer dari blog ini

Using ultrasonic sensor without arduino

Gambar
Using ultrasonic sensor without arduino Parts list: IC 555 IC KA2284 LED(5pcs) Ultrasonic receiver & transmitter Resistor 1K Resistor 2.2K Resistor 10K Resistor 100 ohm Potentiometer 10K (2pcs) Capacitor 10uF (4pcs) Capacitor 3.3nF Transistor 2N2222 Buzzer There are 2 ways to using Ultrasonic sensor without microcontroller: First way, the buzzer turns ON when you put your hand near the sensor   Second way the LED bar show you the distance level between the sensor and the objects. Video: More information in the video
Baca selengkapnya

Electronic load using Op-Amp IC 358

Gambar
Electronic load using Op-Amp IC 358 In this circuit i using IC 358 and some few components to make a simple constant load.  The trick here is connecting a dc voltmeter to the non-inverting input of the op-amp to preset the current before connect it to the battery or the super cap. under test. For more explanation you can watch the video below. Parts list: LM358 : https://www.banggood.com/custlink/Dvv3hO51Df High power resistor: https://www.banggood.com/custlink/K3GvYjHwRm Digital DC Voltmeter: https://www.banggood.com/custlink/3vmDYL5TDU Copper board: https://www.banggood.com/custlink/3KDDmMsPSc MOSFET IRFZ44N : https://goo.gl/35n5Tb   Potentiometer 100K : https://goo.gl/dKnWCj Resistor kit (10 Ohm): https://goo.gl/TgSaff Heatsink: https://www.banggood.com/custlink/D3KGdOSmzf   Circuit:   Gerber file: Download the Gerber file from here:  https://drive.google.com/open?id=1Lx8xjfkyYPvvzAbA0ponFBYBTQDqrMvU Video: For more explanation you can watch the video below 
Baca selengkapnya

Arduino 220V AC Power meter using PZEM004T

Gambar
Arduino 220V AC Power meter using PZEM004T Library : https://github.com/olehs/PZEM004T Part list: Arduino board LCD 16x2 PZEM004T module Resistor 220 ohm Potentiometer 10K Video:  CODE: #include <SoftwareSerial.h> // Arduino IDE <1.6.6 #include <PZEM004T.h> #include <LiquidCrystal.h> LiquidCrystal lcd(7, 8, 9, 10, 11, 12); PZEM004T pzem(2,3);  // (RX,TX) connect to TX,RX of PZEM IPAddress ip(192,168,1,1); void setup() {   Serial.begin(9600);   pzem.setAddress(ip);   lcd.begin(16, 2); // lcd rows and columns    } void loop() {     float v = pzem.voltage(ip);   if (v < 0.0) v = 0.0;   Serial.print(v);Serial.print("V; ");   lcd.setCursor(0,0);   lcd.print("V= ");   lcd.setCursor(2,0);   lcd.print(v);   float i = pzem.current(ip);   if (i < 0.0) i = 0.0;   Serial.print(i);Serial.print("A; ");   lcd.setCursor(9,0);   lcd.print("A= ");   lcd.setCursor(11,0);   lcd.print(i);   float p = pzem.power(ip);   if (p < 0.0) p = 0
Baca selengkapnya