Auto light switch for bathroom using laser and IC4017

Many people forgets the bathroom and toilet lamps in ON state, absolutely this causes increasing electric bill and even decrease lamps lifespan. This circuit is a simple way to turning ON and OFF the bathroom or toilet lamp automatically without using microcontroller.
The circuit based on the counter IC4017 and laser. when a person go to bathroom his body cut the laser ray that is focused on the LDR in another side of the door frame, connecting and disconnecting the laser ray changed the LDR electric resistance and giving a positive signal to pin14 of the IC4017 through transistor 2N2222, since pin4 jumped to reset pin (pin15) so the output selector will be changed between pin3 and pin2. Pin3 run the transistor to running the relay.
Two LEDs showing ON state and OFF state. 330 ohm resistor used to LEDs protection by giving 15mA current to them.
You can use any other NPN transistor rather than 2N2222 such as BC547, C9013, 2N5551, etc. 
This circuit is suitable for light switching for any place that used by one person such as toilet and bathroom, you can't use it for the room because when second person coming  inside the room the lamp will be turns OFF.

Part list:
IC4017
Transistor 2N2222
Laser 5mW
Relay 5v 
LEDs
LDR
Resistor 1K
Resistor 200K
Resistor 2.2K
Resistor 330R
Capacitor 10nF
Diode 1N4007


Auto light switch for bathroom using laser and IC4017

Auto light switch for bathroom using laser and IC4017

In following video you can watch how the circuit works:
Please subscribe to my YouTube channel here: 
https://www.youtube.com/c/EngMousaalkaabi?sub_confirmation=1


Komentar

Posting Komentar

Postingan populer dari blog ini

Using ultrasonic sensor without arduino

Gambar
Using ultrasonic sensor without arduino Parts list: IC 555 IC KA2284 LED(5pcs) Ultrasonic receiver & transmitter Resistor 1K Resistor 2.2K Resistor 10K Resistor 100 ohm Potentiometer 10K (2pcs) Capacitor 10uF (4pcs) Capacitor 3.3nF Transistor 2N2222 Buzzer There are 2 ways to using Ultrasonic sensor without microcontroller: First way, the buzzer turns ON when you put your hand near the sensor   Second way the LED bar show you the distance level between the sensor and the objects. Video: More information in the video
Baca selengkapnya

Electronic load using Op-Amp IC 358

Gambar
Electronic load using Op-Amp IC 358 In this circuit i using IC 358 and some few components to make a simple constant load.  The trick here is connecting a dc voltmeter to the non-inverting input of the op-amp to preset the current before connect it to the battery or the super cap. under test. For more explanation you can watch the video below. Parts list: LM358 : https://www.banggood.com/custlink/Dvv3hO51Df High power resistor: https://www.banggood.com/custlink/K3GvYjHwRm Digital DC Voltmeter: https://www.banggood.com/custlink/3vmDYL5TDU Copper board: https://www.banggood.com/custlink/3KDDmMsPSc MOSFET IRFZ44N : https://goo.gl/35n5Tb   Potentiometer 100K : https://goo.gl/dKnWCj Resistor kit (10 Ohm): https://goo.gl/TgSaff Heatsink: https://www.banggood.com/custlink/D3KGdOSmzf   Circuit:   Gerber file: Download the Gerber file from here:  https://drive.google.com/open?id=1Lx8xjfkyYPvvzAbA0ponFBYBTQDqrMvU Video: For more explanation you can watch the video below 
Baca selengkapnya

Arduino 220V AC Power meter using PZEM004T

Gambar
Arduino 220V AC Power meter using PZEM004T Library : https://github.com/olehs/PZEM004T Part list: Arduino board LCD 16x2 PZEM004T module Resistor 220 ohm Potentiometer 10K Video:  CODE: #include <SoftwareSerial.h> // Arduino IDE <1.6.6 #include <PZEM004T.h> #include <LiquidCrystal.h> LiquidCrystal lcd(7, 8, 9, 10, 11, 12); PZEM004T pzem(2,3);  // (RX,TX) connect to TX,RX of PZEM IPAddress ip(192,168,1,1); void setup() {   Serial.begin(9600);   pzem.setAddress(ip);   lcd.begin(16, 2); // lcd rows and columns    } void loop() {     float v = pzem.voltage(ip);   if (v < 0.0) v = 0.0;   Serial.print(v);Serial.print("V; ");   lcd.setCursor(0,0);   lcd.print("V= ");   lcd.setCursor(2,0);   lcd.print(v);   float i = pzem.current(ip);   if (i < 0.0) i = 0.0;   Serial.print(i);Serial.print("A; ");   lcd.setCursor(9,0);   lcd.print("A= ");   lcd.setCursor(11,0);   lcd.print(i);   float p = pzem.power(ip);   if (p < 0.0) p = 0
Baca selengkapnya